6X-44MAG [6-Shot .44Mag] Speedloader, Block, Stand, or Pouch

Description

6X-44MAG Speed Loaders and Accessories,
use drop-down menus to select configuration, ammo not included.
Made in the U.S.A.
The 6X-44MAG Speed Loaders and Blocks are CNC machined to fit the following 6-Shot .44 ag caliber revolvers
:
Smith & Wesson
- 21, 24, 29, & 629
Taurus
- Raging Bull .454
Dan Wesson
Ruger
- Redhawk 44 &.45
Ruger
- Super Redhawk
Colt
- Anaconda
The
Speed Loader
(upper left corner of image)
- Available Singly, in Pairs, or in combination with a Block, Mount, Stand or Pouch.
- Machined from solid billet aluminum,
- Utilize internal O-rings which reduce the need for lubrication,
- Available Natural Bare Metal or Anodized Tactical Black or Zombie Green.
The
Bedside Block
(upper center of image)
- Holds
Two
Full Reloads, and is available By Itself, or with 1 or 2 Speedloaders.
- Machined from a 4 inch by 2 inch piece of aircraft aluminum that is 3/4 inch thick.
- Available Natural Bare Metal or Anodized Tactical Black or Zombie Green.
The
Range Block
(upper right corner of image)
- Holds
Eight
Full Reloads, and is available By Itself, or with 1 or 2 Speedloaders.
- Machined from a 7 inch by 3.5 inch piece of aircraft aluminum that is 3/4 inch thick,
- Only comes in the Bare Natural Finish, and will not be anodized.
The
Hard Dupot Hytrel Double
Pouch
(lower left corner of image)
- Holds
Two
Loaded .44/.45 Speedloaders, and is available with 2 Speedloaders.
- Fits 2¼" or smaller belt (not included).
- Nickel snaps closure.
- Available in Basket-Weave Finish (shown) or Plain Finish (not shown).
- Only available in Black color.
- Manufactured by HKS.
The
Soft Cordura Nylon Double
Pouch
(lower center of image)
- Holds
Two
Loaded Speedloaders, and is available with 2 Speedloaders.
- Fits 2¼" or smaller belt (not included).
- Velcro closure.
- Available in Black (shown) or Camo (not shown).
- Manufactured by HKS.
The
Range Stand
(lower right corner of image)
- Holds
Four
Full Reloads, and is available By Itself, or with 1 or 2 Speedloaders.
- 1/4" stainless steel rod in the optimal angle to hold your firearm.
- Machined from a 7 inch by 3.5 inch piece of aircraft aluminum that is 3/4 inch thick,
- Only comes in the Bare Natural Finish, and will not be anodized.
Notes
: If your revolver is not listed, the speedloader may not fit--check with the gun manufacturer. If the cylinder dimensions are the same as a listed revolver, then they might use the same speedloader. Whether your gun is
listed or not
, with the cylinder fully open there must be a straight path for all rounds to load simultaneously, plus a small allowance for the thickness of the side of the speedloader. If your revolver's grip or cylinder release is in the way of the speedloader, the grip or cylinder release may need to be replaced or modified. Make sure the round count of your cylinder matches that of the speedloader. Listed above is the extent of what has been tested by the manufacturer or reported by other customers as working--if your gun is not listed we have no further information.
Directions for use:
Fill the block with the ammo of your choice
Turn post of speed loader Counter-clockwise releasing the key
Place speed loader over the rounds
Turn post clockwise to lock on the rim of the casing
Place rounds into the firearm cylinder
Turn post counter-clockwise to release rounds into your cylinder
NOTE:  Stock images shown demonstrate possible combinations, may not be actual configuration nor quantities ordered, see description and options for what you are ordering.  Use drop-down menus to select configuration--available with or without speedloaders and with or without the block or pouch.
NOTE: UPS and FedEx will not be used for deliveries to PO Boxes, APO/FPO/DPO, and the US Protectorates--orders placed as such will either be canceled or shipped via the Postal System at our discretion.